|
Lid Supports from Rockler
|
|
|
 Adjustable Lid Support
This is the lid support for a variety of applications! It is convertible since it can be installed on either horizontal or vertical, for lids or drop fronts. It is reversible to be mounted left or right, and change tension direction from lift-up to drop-down as needed.It's adjustable: Tension adjustment can be made easily using a number 4 Allen wrench for lids or drop fronts up to 20 lbs. The angle opening can be set at 75 degrees or 90 degrees depending on how brackets are mounted. It's even demountable: Brackets can be mounted without the support arm attached, and the support arm can be removed! Lid or drop-front requires separate hinges.
|
 Mini Concealed Soss Hinge
3/8' Wide x 1' Long. For 1/2'-thick material.Price per pair.
|
 Solid Brass SmallBox Cylinder Hinges
Solid brass hinge for those small jewelry or pencil boxes. Installation requires cutting a 45 degree bevel and drilling 5mm holes. Hinge is 15mm (9/16") long overall x 5mm (3/16") diameter. 10 per pack.
|
 Solid Brass SmallBox Hinge
The full mortise hinge provides a built-in stop, allowing a lid to remain open at about 95°. For use when an additional stay is not desired.The hinge is mortised flat into the box and lid.
|
 Solid brass Jewelry Box Stop Hinges
|
 Jewelry Box Tray Support
Lifts and lowers the jewelry box tray when lid opens and closes. By lifting the top tray, the support provides access to the jewelry below. Measures 7' long overall. Use with a 95 stop hinge. Solid Brass. Price per pair.
|
 Jewelry Box Lid Support
Cut a mortise 1/4' wide x 2-7/8' long x 1/2' deep to install. Solid brass.
|
 Jewelry Box Tray Support
Lifts and lowers the jewelry box tray when lid opens and closes. By lifting the top tray, the support provides access to the jewelry below. Measures 7' long overall. Use with a 95 stop hinge. Solid Brass. Price per pair.
|
 Solid Brass Quadrant Hinge
Hinge measures 1' x 1' x 1-1/4' overall. Requires an additional 1-1/4' deep mortise for the support arm. Use with a minimum of 3/8' thick material. price per pair.
|
 Solid Brass Small Box Hinges
|
 HeavyDuty Soft Down Lid Support
With a range of 60-86' /pound per support and 121-173' /pound per pair (formula: lid wt. x front-to-back size ÷ 2 =' /pounds), these heavy-duty supports offer the security of gentle descent for larger applications. Opening to 70º, they are ideal for both overlay and inset lids. Requires 5-1/8' x 7/8' x 10-3/4' for mounting. Overall dimensions are 5-1/2' L x 1-5/8' High x 3/4' thick; arm is 10inches L when fully extended. Available in right- and left-handed.
|
 Trunk Lid Support
Plated steel support measures 6-7/16' center to center and 6-7/8' long overall. 7/16' wide. Screws included.Price per pair.
|
 Briefcase Support
Reversible support. 3-3/4' center to center. 4-3/16' overall. Price for each.
|
 Trunk Strap Hinges
Made from stamped steel and then plated for decorative appeal. 90 stop hinges. Price per pair.
|
 90 Stop Hinges
|
 Case Catch
Catch has an attractive profile. 1-1/4' Wide x 1-5/8' H. Comes in either brass plated or nickel plated finish. Price per pair.
|
 Classic Oblong Catch
Quality catches with the traditional shape used on many trunks and chests. Small catch- 1-1/2' W x 2-3/4' H- 2 per pack.
|
 Classic Oblong Catches
|
 Locking Drawbolt
This fine brass plated drawbolt locks easily with a turn of a key. The lock is stamped steel with brass plating. Heavy duty. Keyed alike and supplied with one key (#151).1-3/4' W x 3-3/8' L Overall 5/8' projection.Comes with #4 X 3/4' oval head screws for mounting. Surface mounted.
|
 Catch with Padlock Hasp
Plated steel. 2 per pack.
|
 Spring Trunk Lock
Beautiful lock! The hasp opens to 135°. 3-3/4' wide x 4- 13/16' high. Brass plated.
|
 Figure 8 Trunk Lock
Coordinate with matching corners. 3-3/4' W x 6-5/8' H. Surface mounted. Price for each.
|
 Basic Economy Drop Front Support
|
Trunk Lid Support
Plated steel support measures 6-7/16' center to center and 6-7/8' long overall. 7/16' wide. Screws included.Price per pair.
|
 Cedar Chest Hinge and Lid Support
This time tested classic design has been used on cedar chests and hope chests for many years. Sturdily constructed from brass plated steel. Mounts to side of case and underside of flat lid. Allows lid to open to approximately 95 degrees. Screws included.Price per pair.
|
 Lift Up Door Support
To close, lift slightly and the support easily disengages. One support is required for small to medium doors. Nickel plated steel. 12' overall.
|
 Solid Brass Hardware
Study construction. Solid brass with a polished, lacquered finish. Dual purpose lid support or drop front. (right and left hand are designated by drop front use as you face the desk). Overall length is 9-3/4' . Each arm is 4-7.8' long.
|
 Solid Brass Support
Price for each support.
|
 Soft Down Support
Compact design makes these supports ideal for installing in tight places. Use one support per 43' /lbs. Figure' /lbs with this formula: (lid wt. X front to back size) divided by 2. Price for each one.
|
 Soft down support
Lids lower gently--never crushing fingers. Support opens lids to a maximum angle of 105 and is 8-7/8' long overall. They have nickel plated steel arms with cream colored plastic housing. Compact design makes these supports ideal for installing in tight places. Use one support per 43 inch/lbs. Figure inch/lbs with this formula: (lid wt. X front to back size) divided by 2. Price for each support.
|
 Self Balancing Lid Support
Surface mounts only 4-1/2' from back of the cabinet. Statuary bronze finish. (Lid weight times front to back size) divided by 2 equals' pounds range. Use on toy boxes with 3/4' thick backs. Price per pair.
|
 Quiet Action Support
Patented friction discs at the pivot point prevent lids from slamming shut. Lowering action is gentle and controlled. Supports lock when opened and unlock when closed. Smooth, friction free movement at any stopping point. Bronzed steel.
|
 Toy Box Lid Supports
Prevents lids from accidentally slamming shut on fingers. Measures approximately 5' long pivot to pivot in extended position. Use this formula to choose your supports: (lid wt. times front to back size) divided by 2 = inch lbs range. Use on toy boxes with 3/4' thick backs. Statuary bronze finish. Price per individual lid support.
|
 Black Jewelry Box Turnbuttons
|
 Brass Jewelry Box Staple Hasp Catch
|
 Brass Jewelry Box Hook
|
 Brass Jewelry Box Handle
|
 Brass Jewelry Box DrawSnap Catch
|
 BrassPlated SmallBox Fastener Hinge
|
 BrassPlated LargeStrap SmallBox Fastener Hinge
|
Contact Us