Clamps Specialty Clamps

Rockler > Specialty Clamps > Clamps

Specialty Clamps from Rockler Select Subcategory Here Specialty Clamps Band Clamps Bar Clamps Clamp-It Handscrew Clamps Miter Clamps Pipe Clamps Specialty Clamps Spring Clamps

Bessey Supergrips 8 These supergrips are designed to ensure that the jaws always remain in the desired position while keeping an even preset clamping pressure, regardless of the distance between the jaws! Features include: nickel plated surfaces durable fully adjustable jaws screws with locknuts for adjusting jaw angle and clamping pressure
Push Down Lever Clamp Bottom of rubber clamp foot adjusts from 3/8" above mounting surface to 5/8" below mounting surface.Total length with arm extended and lever down 5-5/8".Length of arm only, extended is 2-1/4".Mounting plate is 1-3/8" w x 1-1/2" L.Up to 150 pounds of holding power.
Small Push Clamp Plunger travels 5/8".Mounting plate is 1-1/16" W x 1-3/8" L.Does include wood screws for mounting - brass colored.
Small THandle Clamp Bottom of rubber foot adjusts from 1/4" above mounting surface to 3/8" below mounting surface total length with arm extended and T-handle up is 2-5/8" L, Height 2-1/4".Mounting plate is 1-9/16" W x 1" L.
HeavyDuty THandle Clamp Bottom of rubber clamp foot adjusts from 3/16" below mounting surface to 7/8" below mounting surface.Total length with arm extended and T-handle up is 3-3/4" L Height is 2-1/4".Length of arm only, extended is 2".Mounting plate is 2-7/8" W x 2-3/4" L.
HeavyDuty Lever Clamp Bottom of rubber clamp foot adjusts from 5/8" above mounting surface to 3/8" below mounting surface.Total length with arm extended and lever down 7-7/8"Length of arm only, extended is 2-7/8"Mounting plate is 1-3/8" W x 1-1/2 L.
Post Handle Clamp Bottom of rubber clamp foot adjusts from 3/8" above mounting surface to 5/8" below mounting surface.Total length with arm in up position is 4-5/8" and height with arm up is 7-7/8".Length of arm only, extended is 2-7/8"Mounting Plate is 1-13/16" W x 1-3/8" L.
Large Push Action Clamp Bottom of rubber clamp foot adjusts from 3/8" above mounting surface to 5/8" below mounting surface.Total length with arm extended and lever down 5-5/8".Length of arm only, extended is 2-1/4".Mounting plate is 1-3/8" w x 1-1/2" L.
Bora 3Way Edge Clamp 4-1/2" clamp capacity.3" total throat depth.Secondary clamp has 3/8" throw.Non-marring pads on all clamping surfaces.Lightweight aluminum construction.Molded for strength.
Large Toggle Clamp Foot Standard 5/16"-18 TPI stud size works with most existing toggle clamps.Foot has an overall diameter of 1-5/8", with a soft clamping pad that measures 1-3/8" in diameter.Works great for pocket hole assembly jigs!
Single Sided VClamp Vacuum Clamps V-Clamps are designed to hold non-porous objects using compressed air. Simply connect it to your compressed air supply. Ideal for objects with at least one relatively flat face, but slightly curved items such as guitars and violins work very well. Rough sawn timbers can also be clamped.There are no moving parts inside the clamps, so the only thing that can wear out is the replaceable rubber seal. Use 6mm (1/4") pressure hose to string multiple clamps together from one air supply - great for large tabletops!Single-Sided V-ClampMeasures 6-1/4" x 6-1/4" x 7/8".Seal Channels have 1-7/8" spacing.Includes four 1/4" Fixing holes.Max Holding force with full face - 150kg (330lbs).Air Consumption at 80psi - 26 litres/min, 1cfm.Max supply pressure - 800kPa, 115psi.Vacuum generated at 800kpa, 115psi - -88kpa, -12.5psi, 26" Hg.
Double Sided VClamp Vacuum Clamps V-Clamps are designed to hold non-porous objects using compressed air. Simply connect it to your compressed air supply. Ideal for objects with at least one relatively flat face, but slightly curved items such as guitars and violins work very well. Rough sawn timbers can also be clamped.There are no moving parts inside the clamps, so the only thing that can wear out is the replaceable rubber seal. Use 6mm (1/4") pressure hose to string multiple clamps together from one air supply - great for large tabletops!Double-Sided V-ClampMeasures 6-1/4" x 6-1/4" x 1".Seal channels have 1-7/8" spacing.Max holding force per face - 150kg (330lbs).Air Consumption at 80psi - 55 litres/min, 2cfm.Max supply pressure - 800kPa, 115psi.Vacuum generated at 800kpa, 115psi - -88kpa, -12.5psi, 26" Hg.
Universal Fence Clamps Rigid aluminum body with steel threaded components.Range of travel 1/2"-5-3/4" (1/2" minimum assumes a 3/4" auxiliary fence; you can clamp to an even thinner primary fence if you use a thicker auxiliary fence).Drill a 3/8" hole in the auxiliary fence.
XTreme Tapereg Quick Clamp Wrap 1” Wide x 20 mil Thick x 10’ Long.Great for Automotive, Plumbing, Sports, Outdoor, Electrical, Garden, Tools and Marine applications.No Adhesive, Bonds Only to Itself.After roughly 2 minutes in a wrapped state, the bond becomes permanent.Won’t Melt Up to +500F (+260C).Remains Flexible to -60F (-54C).Forms a Permanent Air & Water Tight Seal.Tensile Strength of 600 psi.Insulates to 8000Volts (for a 20 mil wrap).Stretches to 3 times its Length.Conforms to Irregular Shapes.
Besseyreg EKT55 One Hand Edge Clamp Compound screw mechanism enables you to simultaneously engage the top and bottom pressure pads while applying pressure to the front edge of a countertop.Also works great when bending solid wood edging into curves.All three pressure surfaces are advanced with the turn of a single handle.Large jaws with integral, soft plastic caps for gentle non-slip clamping.Pivoting supports reinforce clamping pressure exerted by jaws.Large opening for clamping up to 2-1/8".3" nominal throat.500 lbs. maximum clamping pressure.Lightweight aluminum frame. Innovative clamp simultaneously engages the top and bottom pressure pads while applying pressure to the front edge of a countertop. Works beautifully when bending solid wood edging into curves.
Ponyreg Cabinet Claw Clamp Set Accuracy is assured with these multi-function clamps. Clamping jaws align and tighten face frames.Drill guide creates fast, accurate pre-drilling placement for pilot hole drilling and screw fastening.PLUS, you can fasten face frames without removing or repositioning the clamps.Die-cast aluminum claws and alignment plate have protective rubber pads to prevent marring.Allows you to install two stiles from 1-1/2" to 2" wide and up to 1-1/2" thick (each).Includes 1/8" drill bit for pre-drilling of fastener pilot hole.
Vacuum Press Kit Vacuum bag with attached one-way valve connects to hand vacuum pump. Requires no electrical power. Purchase additional vacuum bags for multiple setups at the same time. Hand pump easily connects to the valve on the vacuum bag to remove air from the chamber. Heavy-gauge vinyl vacuum bag measures 47" long x 14" wide.It takes less than a minute to pull all the air out of the bag and holds a vacuum up to 25hg (15 psi).One-way valve allows you to move the bag out of the way while waiting for glue to cure.Comes with breather netting to allow air to evenly evacuate the bag, extra sealant tape and instructions.Additional vacuum bag (to have several pieces under vacuum at the same time) and seal tape sold separately.Vacuum bag, valve and hand pump included.Square Vacuum Press Kit includes flexible 26" x 28" 20 mil thick vacuum bag, breather netting and hand vacuum pump with attached one-way valve and sealing tape. Comes with extra sealing tape and instructions.
Irwin CClamps Irwin C-clamps feature double-rolled thread for faster clamping and increased durability.Large swivel pad reduces marring on work surface and increases stability.With large handle for greater clamping pressure with less effort and reduced hand fatigue.Available in 3", 4" and 6" sizes.
Stacking Clamp System Stacking clamp system is as easy as 1-2-3. Just clamp panels, stack 'em high and let 'em dry! Includes six clamps, alignment bars and stabilizer bars.Simply set glued boards in and tighten.Easily remove any boards off the rack.Maximum width is 25' and the length is determined by your workpiece.
PushDown Pushup Vertical Mount Clamps Toggle clamps give you an extra hand in the shop, plus allow maximum clearance loading and unloading work piece! All die-stamped steel parts are deburred, cleaned, and receive a zinc-plated finish that resists corrosion. With oil- and stain-resistant hand grips for safety and comfort. Heavy-duty rivets are used to maintain accuracy and increase endurance. With hardened ground pins and bushings. Vertical Mount Post Handle Clamp - 63469 With push-up action. Up to 350 lbs. of holding power. Arm length 1-1/4. Small Push-Down Lever Clamp - 63437 With new higher base! Up to 150 lbs. of holding power. Base dimension 1-3/8 x 1-1/2. Base height 1-3/4. Arm length 2-1/4. Medium Push-Down Lever Clamp - 63445 Features new higher base! Up to 500 lbs. of holding power. Base dimension 1-3/8 x 1-1/2. Base height 2. Arm length 3. Large Post Handle Push-Up Clamp - 63454 New higher base! Up to 375 lbs. of holding power. Base dimension 1-3/8 x 1-3/4. Base height 2-1/2. Vertical Mount Base Clamp - 63462 With push-down lever action. Up to 150 lbs. of holding power. Arm length 2-3/4.